Mechanical Technician

1. Mechanical Maintenance and Repair Activities - Perform planned preventive, predictive, corrective, and breakdown maintenance activities on assigned mechanical equipment. - Carry out daily inspections, running checks, and maintenance checklists in accordance with approved maintenance schedules. - Monitor the physical condition of equipment and report abnormalities, non-conformances, and developing defects to the Mechanical Maintenance Engineer. - Troubleshoot mechanical failures using approved tools, drawings, manuals, and diagnostic techniques to identify the cause and carry out necessary repairs. - Perform dismantling, inspection, cleaning, repair, replacement, reassembly, alignment, and functional testing of mechanical equipment and components. - Replace defective parts such as bearings, seals, gaskets, O-rings, gland packing, couplings, bolts, filters, strainers, belts, and lubrication-system components. - Perform adjustment, alignment, tightening, lubrication, greasing, oil top-up, oil changing, and cleaning activities in accordance with approved procedures. - Identify and report corrosion, cracks, leaks, overheating, vibration, abnormal noise, misalignment, loose bolts, damaged insulation, and other equipment defects. - Ensure the working area is clean, safe, and properly restored after completion of maintenance activities. v Support maintenance, inspection, and repair of mechanical equipment including, but not limited to: - Siemens 9000HL-Class gas turbine auxiliaries, including lube oil, hydraulic oil, fuel gas, inlet air, ventilation, and turning gear systems. - Steam turbine auxiliaries, including lube oil, gland steam, seal oil, condensate, cooling, and turning gear systems. - Heat Recovery Steam Generator (HRSG), including drums, valves, blowdown systems, expansion joints, and associated auxiliary equipment. - Pumps, including boiler feedwater pumps, condensate extraction pumps, closed cooling water pumps, service water pumps, fire water pumps, fuel oil pumps, chemical dosing pumps, and drainage pumps. - Compressors, blowers, fans, air handling units, ventilation fans, and instrument/service air compressor systems. - Valves, including gate, globe, check, control, safety Valves. - Water treatment, reverse osmosis, condensate polishing, chemical dosing, wastewater treatment, and other balance-of-plant mechanical equipment. 2. Inspection, Testing, and Troubleshooting - Conduct routine inspections and condition assessments of assigned mechanical equipment. - Use approved maintenance and diagnostic tools such as vibration meters, infrared thermometers, laser alignment tools, dial gauges, feeler gauges, torque wrenches, pressure gauges, vernier calipers, and micrometers. - Assist in vibration monitoring, alignment checks, bearing inspections, pump performance checks, valve testing, pressure testing, leak testing, and functional testing. - Record inspection findings, test readings, equipment condition, defects identified, and maintenance work completed. - Assist in identifying the root cause of equipment failures and support implementation of corrective actions. - Monitor repeated failures and report recommendations for repair, modification, replacement, or maintenance-plan improvement. - Support basic welding, fabrication, and workshop repair activities. - Participate in planned shutdowns, major outages, overhauls, commissioning activities, warranty works, and emergency repairs. - 3. Safety, Permit-to-Work, and Compliance - Follow all applicable safety rules, permit-to-work requirements, lockout/tagout procedures, confined-space-entry requirements, lifting procedures, and site safety standards. - Verify that equipment is properly isolated, depressurized, drained, vented, cooled down, and released for maintenance before starting work. - Use required personal protective equipment, approved tools, lifting equipment, and safety devices at all times. - Participate in toolbox talks, risk assessments, safety observations, hazard reporting, audits, and incident investigations. - Immediately report unsafe conditions, leaks, damaged tools, lifting hazards, near misses, and incidents. - Follow environmental and waste-management requirements, including proper identification, handling, segregation, and disposal of waste materials. - Ensure maintenance work complies with approved site procedures, OEM requirements, quality standards, and EHS requirements. 4. Documentation and CMMS Support - Complete maintenance checklists, inspection sheets, work completion records, test reports, and defect reports accurately. - Provide clear feedback to the Mechanical Maintenance Engineer regarding work completed, materials used, defects found, and follow-up actions required. - Support work-order completion, man-hour recording, and equipment-history updates in the CMMS. 5. Spare Parts, Tools, and Housekeeping - Review assigned work orders and identify the required spare parts, consumables, tools, lifting equipment, and test

Mechanical Maintenance and Repair Activities: Perform planned preventive, predictive, corrective, and breakdown maintenance on assigned mechanical equipment; conduct daily inspections, running checks, and maintenance checklists; monitor equipment condition and report abnormalities; troubleshoot mechanical failures using approved tools and manuals; dismantle, inspect, clean, repair, replace, reassemble, align, and test mechanical equipment; replace defective parts (bearings, seals, gaskets, O-rings, gland packing, couplings, bolts, filters, strainers, belts, lubrication components); perform adjustments, alignment, tightening, lubrication, greasing, oil top-up, oil changes, and cleaning per procedures; identify and report corrosion, cracks, leaks, overheating, vibration, abnormal noise, misalignment, loose bolts, damaged insulation, and other defects; ensure a clean, safe work area post-maintenance. Support maintenance, inspection, and repair of equipment including Siemens 9000HL-Class gas turbine auxiliaries, steam turbine auxiliaries, HRSG, pumps, compressors, valves, and water treatment systems. Inspection, Testing, and Troubleshooting: Conduct routine inspections and condition assessments; use tools such as vibration meters, infrared thermometers, laser alignment tools, dial gauges, feeler gauges, torque wrenches, pressure gauges, vernier calipers, and micrometers; assist in vibration monitoring, alignment checks, bearing inspections, pump performance checks, valve testing, pressure testing, leak testing, and functional testing; record findings and maintenance work; assist root-cause analysis and corrective actions; monitor repeated failures and suggest repair or maintenance improvements; support basic welding, fabrication, and workshop repair activities; participate in planned shutdowns, major outages, overhauls, commissioning, warranty work, and emergency repairs. Safety, Permit-to-Work, and Compliance: Adhere to safety rules, permit-to-work, lockout/tagout, confined-space-entry, lifting procedures, and site safety standards; verify proper isolation, depressurization, draining, venting, cooling before maintenance; use PPE and approved tools; participate in toolbox talks, risk assessments, safety observations, hazard reporting, audits, and incident investigations; report unsafe conditions, leaks, damaged tools, lifting hazards, near misses, and incidents; follow environmental and waste-management requirements; ensure work complies with site procedures, OEM requirements, quality standards, and EHS requirements. Documentation and CMMS Support: Complete maintenance checklists, inspection sheets, work completion records, test reports, and defect reports; provide feedback to the Mechanical Maintenance Engineer; support work-order completion, man-hour recording, and equipment-history updates in CMMS. Spare Parts, Tools, and Housekeeping: Review work orders to identify required spare parts, consumables, tools, lifting equipment, and tests.